Covering a sailboat mast up can seem like a very daunting proposition at first, but it takes only a couple of more steps than shrink wrapping a mast down boat. Following the directions below and watching the training DVD at least twice will minimize any problems.
1. Install your strapping fore and aft on the boat from the highest points at the bow and stern. The strapping will be tied around the mast from the stern and then around the mast from the bow (if the boom is left on, it can become part of the support structure aft of the mast, but you must put a 2” x 4” upright under the rear of the boom to give it strength). Pull the strapping tight as you normally would, measure and install your wooden uprights as on a mast down boat, put your lateral straps over the wooden uprights, or boom, and pad them.
2. Install the perimeter band following the DVD instructions.
3. Go aboard the boat with a 25’ tape measure. Measure from the mast back to the farthest point aft (top of the stern rail). To this figure add 2 feet which will extend aft of the mast and 4 feet that will drape over the bow (a total of 6 extra feet).
4. Now measure from the mast forward (top of the bow rail or pulpit). To this figure add on 2 feet which will extend aft of the mast and 4 feet that will drape over the bow (a total of 6 extra feet).
5. Next cut your roll of shrink wrap the measurement from the mast back. Roll it up and take it onto the boat. Lay the roll over the support structure or boom and open it enough to measure and find the center. Make a 2’ lengthwise slit in the shrink wrap at the center of the wrap. This slit area will be wrapped around the mast to form a collar. Once you have a collar formed, take the roll of heat shrink tape and go around the collar twice very tightly (do not stick tape directly to the mast as there might be an adhesive residue in the spring).
6. Unroll the aft section of shrink wrap towards the stern (do not unfold its entire width yet; the wind might catch it). Go aft as far as possible, until you run into the aft stays. Now you can unfold the shrink wrap and have it lay as straight fore and aft, and side to side, as possible. Using your wrap cutting knife make slits in the shrink wrap up to stays and halyards. They should be as neat as possible. Use strips of heat shrink tape to seal them and then apply heat to warm the adhesives (press tape down firmly to remove all air bubbles).
7. Trim and tuck the shrink wrap under the perimeter band on the boat so that wind doesn’t catch it.
8. Now the shrink wrap piece at the bow can be attached. It is done in a similar fashion as the aft piece. Place the measured piece of wrap just forward of the mast; find the center and slice into it 2 feet. Make a collar around the mast tightly and tape around it. Unroll the wrap toward the bow up to the forestay. Slice the wrap to the forestay and roll it over the bow. Tape the slit together and unfold the shrink wrap.
9. Run a strip of tape from the mast down to each side of the shrink wrap where the forward and aft pieces meet. Use the heat tool to warm the adhesives in the tape and actually heat weld the pieces of shrink wrap together.
10. Trim and tuck the forward piece under the perimeter band. Shrink wrap the boat according to DVD.
Please call us at (800) 968-5147 with any questions or email drshrink@dr-shrink.com.
Category: Shrink
SHRINK WRAP KEEPS MACHINERY PROTECTED FROM DAMAGE
For machines to run properly, and look presentable when delivered to your customers, they must be protected during storage and transportation from all weather damage. Dr. Shrink, a full-service supplier of premium shrink wrap and installation accessories, provides a versatile, cost-effective solution that helps ensure equipment stays clean and damage free. At pennies per square foot, shrink wrap provides essential protection to valuable machinery.
Dr. Shrink offers premium shrink wrap in widths of 12 feet to 60 feet with thicknesses from 6 to 12 mil. All materials are 100% virgin resin with maximum UV filtration for long-term usage. When properly installed, white shrink wrap will last more than one year in any climate without becoming brittle due to sun damage.
Shrink wrap has considerable advantages over tarps, construction plastic sheeting and other types of covers that can move and chafe painted surfaces. It can be ventilated to eliminate moisture and mildew, and zipper access doors provide a convenient, easy-entry option. The affordable shrink wrap is also easily recycled through Dr. Shrink’s REBAG recycling program and Recycling Run efforts. For a catalogue, shrinkwrap samples, or additional product information contact Dr. Shrink at 800-968-5147; Fax: 231-723-9586; drshrink@dr-shrink.com.
Shrink Wrap Weekly Bundle 3/2 – 3/8: Zipper Access Door
Free Zipper Access Door
You must add this product into your cart.
Place an order of $125.00 or more this week and you can receive a free 30″ x 36″ Zipper Access Door! *LIMIT ONE PER CUSTOMER, ONE PER WEEK*
You must mention this bundle if you are ordering over the phone. If ordering online, use the promo code is BUNDLE208 at checkout.
**YOU MUST ADD THE WEEKLY BUNDLE PRODUCT INTO YOUR SHOPPING CART IN ORDER FOR THE PROMO CODE TO WORK**
Shrink Wrap Weekly Bundle 2/23 – 3/1: Woven Cord Strapping
Free Roll of 1/2″ x 1500′ Woven Cord Strapping
You must add this product into your cart.
Place an order of $500.00 or more this week and you can receive a free roll of 1/2″ x 1500′ Woven Cord Strapping!
You must mention this bundle if you are ordering over the phone. If ordering online, use the promo code is BUNDLE207 at checkout.
**YOU MUST ADD THE WEEKLY BUNDLE PRODUCT INTO YOUR SHOPPING CART IN ORDER FOR THE PROMO CODE TO WORK**
Allow Entry into Shrink Wrap Covers with Dr. Shrink Zipper Access Doors
Zipper Access Doors
from Dr. Shrink, Inc.
Just because an RV is shrink wrapped for storage doesn’t mean owners shouldn’t be able to get back inside if needed. With Dr. Shrink’s RV Access Door, users can come and go as they please.
The RV Access Door measures 40″ x 82″ and features a new “C” shaped opening versus the traditional “U” shape. A double, pull-heavy zipper enables unlimited usage without compromising the integrity of the cover. While enabling access into an RV, our new 40″ x 82″ clear door is also ideal for construction/scaffolding applications.
Dr. Shrink also stocks standard Zipper Access Doors measuring in widths of 30″ and 36″ with lengths of 36″, 48″ and 72″. These are perfect sizes for installing on a boat during winter storage or heavy machinery as pictured below. All Dr. Shrink’s Zipper Access Doors are re-sealable and waterproof, and are easily installed with heat shrink tape around the door perimeter.
231-723-2685
800-968-5147
drshrink@dr-shrink.com
Shrink Wrap Weekly Bundle 2/16 – 2/22: Strapping Dispenser
Free Dr. Shrink Strapping Dispenser
You must add this product into your cart.
Place an order of $250.00 or more this week and you can receive a free Dr. Shrink Strapping Dispenser!
You must mention this bundle if you are ordering over the phone. If ordering online, use the promo code is BUNDLE206 at checkout.
**YOU MUST ADD THE WEEKLY BUNDLE PRODUCT INTO YOUR SHOPPING CART IN ORDER FOR THE PROMO CODE TO WORK**
Shrink Wrap Weekly Bundle 2/9 – 2/15: Free Can Koozie®
Free Dr. Shrink Can Koozie®
You must add this product into your cart.
Place ANY order this week and you can receive a free Dr. Shrink Can Koozie®!
You must mention this bundle if you are ordering over the phone. If ordering online, use the promo code is BUNDLE205 at checkout.
**YOU MUST ADD THE WEEKLY BUNDLE PRODUCT INTO YOUR SHOPPING CART IN ORDER FOR THE PROMO CODE TO WORK**
Shrink Wrap Weekly Bundle 2/2 – 2/8: Heat Shrink Tape
Free 4″ Heat Shrink Tape
You must add this product into your cart.
Place an order of $225.00 or more this week and you can receive a free roll of 4″ x 180′ Heat Shrink Tape in any color!
You must mention this bundle if you are ordering over the phone. If ordering online, use the promo code is BUNDLE204 at checkout.
**YOU MUST ADD THE WEEKLY BUNDLE PRODUCT INTO YOUR SHOPPING CART IN ORDER FOR THE PROMO CODE TO WORK**
Shrink Wrap Weekly Bundle 1/26 – 2/1: Free Semi-Fit Indoor Storage Cover
Free Semi-Fit Indoor Storage Cover
You must add this product into your cart.
Place an order of $500.00 or more this week and you can receive a free Semi-Fit Indoor Storage Cover!
You must mention this bundle if you are ordering over the phone. If ordering online, use the promo code is BUNDLE203 at checkout.
**YOU MUST ADD THE WEEKLY BUNDLE PRODUCT INTO YOUR SHOPPING CART IN ORDER FOR THE PROMO CODE TO WORK**
See available sizes
Shrink Wrap Weekly Bundle 1/19 – 1/23: Free Roll of Strapping
Free Roll of 1/2″ x 1500′ Woven Cord Strapping
You must add this product into your cart.
Place an order of $500.00 or more this week and you can receive a free roll of 1/2″ x 1500′ Woven Cord Strapping!
You must mention this bundle if you are ordering over the phone. If ordering online, use the promo code is BUNDLE202 at checkout.
**YOU MUST ADD THE WEEKLY BUNDLE PRODUCT INTO YOUR SHOPPING CART IN ORDER FOR THE PROMO CODE TO WORK**
