*To see the entire Weekly Bundle, click here.
Free Dr. Shrink Strapping Dispenser
*To see the entire Blog, click here.
Dr. Shrink’s Zipper Access Doors are tape on the finished cover to allow access into a shrink wrapped object without compromising the durability of the cover.
TRICK – To install our Zipper Access Doors, just follow these simple steps:
1.) A small piece of tape should be placed on each corner to position the door, then tape applied around the entire perimeter. You must tape all 4 sides of the door to the shrink wrap cover. Press and seal the tape to the cover. *It’s important to use Heat Shrink Tape for the best adhesion.
2.) The doors are installed after the shrink wrap has already been heated. They should be installed where there is easy access into the object and on a vertical surface.
3.) Doors should like a big “U” with the curve at the bottom. Make sure to rub out all the air bubbles and to use the Dr. Shrink Film Knife, so your cuts on the end of the tape are clean.
4.) Once the door is taped on, unzip the door and cut out the hole to access the inside of your object.
Click here for our YouTube video with instructions (starts about the 1:25 mark).
TREAT – Today Online Only we’re offering a 10% discount on our 30″ x 36″ Zipper Access Doors. Just enter promo code TREAT26 at checkout.
*This promotion expires at 11:59pm EST on 10/28/16
*To see the entire Blog, click here.
Venting your shrink wrapped object is a simple and easy way to allow airflow under your shrink wrap cover. It reduces moisture buildup without compromising the covers integrity.
The main problem with vents is not having an adequate seal between the vent and the shrink wrap.
TRICK – To install our Weather Tight Self-Adhesive Vent properly and how to prevent from leaking, you just have to follow these simple steps:
1.) Take off the adhesive backing and stick onto the cover.
2.) Pop the cover off of the vent, then cut and remove the shrink wrap from the exposed window.
3.) Grab inside the vent and press firmly around all edges to make sure the vent fully adheres to the shrink wrap. It has a raised lip so it does not allow any leaking into the opening. If there is any gaps between the vent and the shrink wrap, that’s where the leaking will occur.
4.) Pop the top back on and you’re good to go.
Also, click here for our YouTube video with step-by-step instructions.
TREAT – Today only online, we’re offering a 10% discount on our Weather Tight Self-Adhesive Vents. Just enter promo code TREAT16 at checkout.
*This promotion expires at 11:59pm EST on 10/27/16
*To see entire Bundle, click here.
Free Dr. Shrink Re-usable Bag!
*You must add this product into your cart.
Place any size order this week and receive a free Dr. Shrink Re-usable Bag! *LIMIT ONE PER CUSTOMER, ONE PER WEEK*
You must mention this bundle if your are ordering over the phone. If ordering online, use the promo code BUNDLE294 at checkout.
**YOU MUST ADD THE WEEKLY BUNDLE PRODUCT INTO YOUR SHOPPING CART IN ORDER FOR THE PROMO CODE TO WORK**
Click here to add to cart.
*To see the entire Blog, click here.
Viking Cylinders® Lightweight Composite Propane Tanks are designed to replace those heavy propane cylinders. They are 50% lighter than steel tanks and come with a comfortable, ergonomic handle that allows for easy stacking and carrying. The outer walls are translucent, allowing you to see exactly how much propane is left in the tank. Each cylinder has a wide, stable base that prevents it from tipping over.
Unlike steel and aluminum tanks, Viking Cylinders® will not BELVE in a fire. BELVE is the technical abbreviation for Boiling Liquid Expanding Vapor Explosion. In layman’s terms, the cylinder will not explode in a fire. Instead, the resin will burn off, the plastic liner/casing will melt, and the LPG will “breathe” through the cylinder wall, while burning in a controlled manner.
Dr. Shrink carries 3 sizes of Viking Cylinder® Tanks:
11 pound tank – Height: 15.1 inches
Diameter: 12 inches (color may vary)
17 pound tank – Height: 18.3 inches
Diameter: 12 inches
22 pound tank – Height: 22.5 inches
Diameter: 12 inches
Each tank comes with a Filling Certificate.
If you have any questions, please don’t hesitate to give us a call at 800.968.5147 or email us, we’d be happy to help.
*To see entire Weekly Bundle, click here.
Free Zipper Access Door
Place an order of $125.00 or more this week and you can receive a free 30″ x 36″ Zipper Access Door! *LIMIT ONE PER CUSTOMER, ONE PER WEEK*
You must mention this bundle if you are ordering over the phone. If ordering online, use the promo code is BUNDLE293 at checkout.
**YOU MUST ADD THE WEEKLY BUNDLE PRODUCT INTO YOUR SHOPPING CART IN ORDER FOR THE PROMO CODE TO WORK**
*To see the entire Blog, click here.
Our Weekly Bundles give you a chance to get a free product with your order. All you have to do is reach a certain price point and you’ll be eligible for the free product that week. If ordering over the phone, simply mention the Bundle Item and if ordering online, add the product into your cart and then enter the promo code during checkout.
Below are some of the products that you could get FREE – Click to subscribe today!
If you are not part of our Weekly Bundle Blast, you’re missing out on free products that are available every week!
Dr. Shrink’s Strapping Dispenser – Allows users to free up their hands while shrink wrapping, keeps your woven cord strapping free of knots and tangles and has non-skid pads on the bottom so your dispenser will stay put while you unroll your necessary footage for your job. It works on all sizes of strapping.
Zipper Access Door – Our 30″ x 36″ zipper access doors are taped on the finished boat cover to allow access into a shrink wrapped object without compromising the durability of the cover. Comes in either blue, white or clear.
1/2″ x 1500′ Woven Cord Strapping – Is used with wooden uprights and buckles to form the support structure under the shrink wrap cover. It’s also used to create the perimeter band that will secure the shrink wrap material.
4″ Heat Shrink & Preservation Tape – Our Heat Shrink tape is a 9mil polyethylene tape that is designed to install doors and seal pleats, seams and holes. Our Preservation Tape is a 10mil, waterproof tape that contains UV inhibitors for long term storage and leaves minimal adhesive residue.
*To see the entire Weekly Bundle, click here.
Free Roll of 4″ Heat Shrink Tape
Place an order of $225.00 or more this week and you can receive a free roll of 4″ x 180′ Heat Shrink Tape in any color!
You must mention this bundle if you are ordering over the phone. If ordering online, use the promo code is BUNDLE292 at checkout.
**YOU MUST ADD THE WEEKLY BUNDLE PRODUCT INTO YOUR SHOPPING CART IN ORDER FOR THE PROMO CODE TO WORK**
*To see the entire Newsletter, click here.
“Dr. Shrink has been busy traveling all over the world and you can tell that fall season is officially in full swing. Don’t forget to take care of all those summer fun toys – your pontoons, jet skis, patio/lawn furniture, grills, etc. – get them wrapped and protected against the harsh elements that are coming. As always, don’t hesitate to give us a call or send me an email with any questions or comments. Keep a watch for our Halloween “Tricks & Treats” promotion that we’ll be running this month as well. Have a safe and Happy Halloween!
– Mike Stenberg
President & CEO, Dr. Shrink, Inc.
Would you be able to correctly label the products pictured here in the shrink wrap process? Are you currently using all of these products and installing them properly when you shrink wrap boats for storage? It’s time for a quick refresher course from the professionals at Dr. Shrink!
Below is a quick refresher training video on how-to shrink wrap a boat. This quick 8-minute video shows you how to wrap a boat for storage with a support structure. Dr. Shrink, Inc. supplies premium, 100% virgin resin shrink wrap in widths of 12′ to 60′ in a variety of lengths and mil-thicknesses. 6 and 7-mil shrink wrap is recommended for boat storage. Dr. Shrink also supplies a complete line of installation accessories — everything you need to complete your shrink wrap job from start to finish.
—————————————————————————————————————————————————————
Visit our YouTube channel and How To Videos & PDFs section on our website for all the tips, tricks and helpful tools you’ll need. If you have any questions, please don’t hesitate to contact us anytime at 800.968.5147 or email us.
Shrink wrapped 1972 Fighter Jet by Jason Hebb in Delta, BC, CANADA.
Jason said that he had a collector had asked him to wrap the fighter jet for outdoor storage. It only took him an hour and installed the shrink wrap so that it could still roll on it’s wheels. Great work, Jason!
To help protect a boat’s finish from marks caused by boat lift slings during launch and haul-out, international premium shrink wrap supplier, Dr. Shrink, now offers Sling-Shield in three different widths to accommodate all sling sizes. Made with a 6 or 8-mil white polyethylene material, the Sling-Shield has been formulated specifically for use on boat lift slings and fork lift tines.
Made from 100% virgins resins, the Sling-Shield is designed to resist tearing and punctures. Sling-Shield is also easy to keep clean as dirt and grime can just be pressure washed away. This product is simple to install and only requires on person to get the job done. In addition to it’s use on boat lift tines, Sling-Shield is great for protecting sail boat masts during transportation. It’s also helpful as a ventilation tube, when used with a fan to allow airflow into boats during service and manufacture.
Sling-Shield was developed by Euroglass and is available in three widths: 16″ for standard slings, 18″ for sling with rub-rail pads, and now in 36″ wide for covering even the largest of yacht slings (100 ton and larger). All rolls come 600′ long and prices start at $207.00 for a 16″ wide roll. A poly vinyl tape that is used to hold the Sling-Shield to a desired location on a boat lift sling is also offered by Dr. Shrink.
Dr. Shrink has all of the installation accessories you need to make your shrink wrap job easier, faster, and cleaner. Our most popular boat/marine accessories are our Weather-Tight Self-Adhesive Vents, Heat Shrink Tape, End and Bottom Caps, our Professional Film Cutting Knife and Ring Cutter.
Venting is one of the most important parts of wrapping a boat. A properly ventilated cover will allow cross-flow ventilation throughout the cover, minimizing chances of excess moisture and mildew. Our Weather-Tight Self-Adhesive Vents are easy to install using the one-piece pull tab that exposes over 15 square inches of adhesive. They are water resistant and can be installed either horizontally or vertically.
Our Heat Shrink Tape is a 9-mil polyethylene tape that is designed to install doors and seal pleats, seams and holes. It also has a powerful backing that adheres nicely to shrink wrap. Comes in blue, white or clear and a variety of sizes.
The End Caps and Bottom Caps are designed to fit on the top and bottom of 2×4 boards commonly used as support poles under shrink wrap covers. The End Caps have slits every 90° for the woven cord strapping to slide into and when the cover is shrunk, the sections flex downward forming a protective pad on the top to eliminate pole poke-through. Bottom Caps have non-skid discs attached for added stability.
The Professional Film Cutting Knife is used to safely and smoothly cut shrink wrap during installation. No danger of scratching or cutting with it’s hooked end. The Ring Cutter is a convenient strap cutting tool that allows you to keep a blade available throughout the shrink wrap process and cuts woven cord strapping with ease.
Don’t forget when you order – do you have enough: tape, vents, strapping, buckles or zipper access doors? These are our most typical reorder items and can be easily added to any order.
*To see the entire Weekly Bundle, click here.
Free Wrap n Strap Knife (DS-008)
Place any size order this week and you can receive a free Wrap n Strap Knife!
You must mention this bundle if you are ordering over the phone. If ordering online, use the promo code is BUNDLE291 at checkout.
**YOU MUST ADD THE WEEKLY BUNDLE PRODUCT INTO YOUR SHOPPING CART IN ORDER FOR THE PROMO CODE TO WORK**
